APPENDIX B ERROR MESSAGES


The error messages are divided into three sections which refer to the processing phase during which the error occured. Error messages are listed in numerical order within each section. A letter 'W' following the error number indicates that the message is a warning and processing is continued.

B.1 TRANSLATION Errors

1 INVALID CHARACTER IN PRECEDING STATEMENT - 2 I.L. STORAGE EXHAUSTED. FURTHER CALLS CAUSE DATA LOSS 3 ARGUMENTS CANNOT PRECEDE OPCODE. CALL IGNORED 4 OPCODE CALL PRECEDED RELEASE. PREVIOUS LINE LOST 7 PARAMETRIC SURFACE IS NOT NAMED. SURFACE IS UNDEFINED 9 PARAMETRIC SURFACE VARIABLE IS NOT A SCALAR.SURFACE IS UNDEFINED 10 MODIFIER IS NOT DERIF OR NODER. SURFACE IS UNDEFINED 11 PARAMETRIC SURFACE DEFINITION STATEMENT HAS IMPROPER LENGTH. SURFACE IS UNDEFINED 12 NO PARAMETERS FOLLOW COMMAND 13 NO SURFACE IS NAMED. COMMAND IGNORED, CONTINUING 14 W TAGTBL MAY OVERFLOW. TOO MANY CHECK SURFACES 15 TOO MANY SYSTEM-GENERATED LABELS; TABL LENGTH EXCEEDED 16 W SYMBOL EXCEEDS SIX CHARACTERS; IT MAY BE TRUNCATED 17 NAME FOLLOWING CALL/ IS NOT A PREVIOUSLY DEFINED MACRO NOR IT IS A SYSTEM MACRO 18 UNKNOWN FORMAT USED IN OBTAIN STATEMENT 19 TOO MANY ARGUMENTS IN CANON OR OBTAIN STATEMENT; CANSTK ARRAY EXCEEDED 20 LINUSD TABLE USED IN MACRO PROCESSING IS OVERFILLED. SEE APT SYSTEM 21 TOO MANY MACRO VARIABLES IN PART PROGRAM. MACDF1 AND MACDF2 TABLES EXCEEDED 22 TOO MANY VALUES ASSIGNED TO THE MACRO VARIABLES IN PART PROGRAM 23 TOO MANY VALUES ASSIGNED TO THE MACRO VARIABLES IN PART PROGRAM. MACHST TABLE EXCEEDED 24 MACRO NEST LEVEL MAXIMUM EXCEEDED. MACSV1,MACSV2, MACSV3 TABLES EXCEEDED 26 MAS TABLE USED IN MACRO PROCESSING IS FILLED. SEE APT SYSTEM 27 MORE THAN 50 MACROS IN PART PROGRAM. MACSEQ TABLE EXCEEDED 28 TOO MANY MACRO VARIABLES HAVE BEEN ASSIGNED MACRO NAMES 29 VBLSAV TABLE OVERFLOW.REDUCE NUMBER OF MACRO CALLS AND/OR NUMBER OF MACRO VARIABLES 31 MACSPD TABLE USED IN MACRO PROCESSING IS FILLED. SEE APT SYSTEM 32 TOO MANY MACRO VARIABLES IN A SINGLE EXPRESSION 35 TOO MUCH MACRO TEXT 36 NUMERIC NAME TABLE OVERFLOW 37 INVALID USE OF WORD TERMAC 38 SUPPOSED PROCEDURE DOES NOT HAVE CLASS PROCEDURE OR FUNCTION. SEE APT SYSTEM PROGRAMMER 40 W LABARY TABLE FILLED. NO FURTHER SEARCH FOR MISSING LABELS 50 W GEOMETRIC VARIABLE BEING USED HAS BEEN PREVIOUSLY DEFINED WITH THE SAME MODE. FIRST DEF. OVERRIDDEN 52 W TABCYL-VARIABLE BEING USED HAS BEEN PREVIOUSLY DEFINED. FIRST DEF. OVERRIDDEN 53 TOO MANY LARGE DATA ARRAY DEFINITIONS. CANSIZ TABLE FILLED 55 W MISSING FINI. FINI INSERTED AND PROCESSING CONTINUES 56 W MISSING TERMAC. FINI INSERTED AND PROCESSING CONTINUES 71 SEGMENT READ OR FIRST CALL TO SYSTEM MACRO CANNOT BE CONTAINED IN A SEGMENT READ OR A SYSTEM MACRO 72 UNABLE TO OPEN LIBRARY APTLIB. COULD RESULT FROM CALL TO UNDEFINED MACRO 73 SEGMENT NAMED IN READ/ STATEMENT IS NOT IN APTLIB 74 UNABLE TO READ A RECORD FROM APTLIB; I/O ERROR OR ILLEGAL BLOCKSIZE OR RECORD SIZE 101 MISSING TYPE OF SSURF OR SCURV DEFINITION. SURFACE IS UNDEFINED 102 MISSING MODIFIER OF SURFACE TYPE. SURFACE IS UNDEFINED 103 TOO MANY SURFACE NORMALS IN PATCH DEFINITION. SURFACE UNDEFINED 104 THE NEXT ENTRY SHOULD BE A POINT OR VECTOR.SURFACE IS UNDEFINED 105 TOO MANY ARGUMENTS FOR A PATCH DEFINITION.SURFACE IS UNDEFINED 107 TOO MANY VECTORS INPUT AFTER A POINT. ENTRY IGNORED. CONTINUING 109 MAJOR WORD SSURF OR SCURV IS MISSING; SURFACE UNDEFINED 111 MORE THAN 30 POINTS IN A DEFINITION 112 MORE THAN 60 SEGMENTS IN A DEFINITION 1001 GEOMETRIC VARIABLE BEING USED HAS BEEN PREVIOUSLY DEFINED WITH A DIFFERENT MODE. FIRST DEF. RETAINED 1002 W MISSING LABEL STATEMENT ADDRESSED BY JUMPTO OR IF 1003 DUPLICATE LABEL 1004 MIXED MODE 1005 INVALID USE OF MINUS SIGN 1007 INVALID STATEMENT IGNORED 1008 IMPROPER ARGUMENT 1009 W MISSING LABEL. STATEMENT NOT REACHABLE 1010 MATRIX MUST FOLLOW 1011 NOMORE MUST FOLLOW 1012 MIXED MODE 1013 VARIABLE IS UNRESERVED 1014 NO TYPE FOR VARIABLE 1015 SURFACE TYPE CHANGED IN NESTED GEOMETRIC DEFINITION 1016 MACRO DEFINITION NESTED 1017 MACRO NAME NOT PRECEDED BY CALL 1018 DUMMY VARIABLE EXPECTS MACRO NAME 1019 DUMMY VARIABLE REJECTS MACRO NAME 1020 UNKNOWN MACRO VARIABLE 1021 ERROR IN FINAL MACRO PROCESSING 1023 ILLEGAL MODE FOR TEMPORARY IN CALL TO MACRO 1024 VARIABLE NAME IN CANON DEFINITION IS OF INCORRECT MODE 1025 INVALID TABCYL DEFINITION 1026 INVALID TABCYL USED IN RLDSRF DEFINITION 1028 INPUT STATEMENT IS TOO LONG. STACK OVERFLOW 1029 BOUNDED GEOMETRY MUST NOT BE SUBSCRIPTED. STATEMENT IGNORED 1032 INVALID ARGUMENT IN A LARGE DATA CANON STATEMENT 1035 OBTAIN STATEMENT SPECIFIES MORE VARIABLES THAN THERE ARE ELEMENTS IN INDICATED SURFACE CANONICAL FORM 1041 ILLEGAL PATERN DEFINITION FORMAT 1050 WRONG SURFACE ASSOCIATED WITH VARIABLE IN OBTAIN STATEMENT 1111 ILLEGAL SUBSCRIPTED VARIABLE. CHECK FOR MISSING RESERV 2001 FORMAT UNKNOWN OR SOME PARAMETERS ARE UNDEFINED 2002 W ILLEGAL ARGUMENT IN POSTPROCESSOR STATEMENT 2003 ILLEGAL GODLTA STATEMENT 2004 NO DRIVE SURFACE NAMED AFTER GO/, ENTERING RESTART 2005 ITEM NOT FEDRAT, TO, ON, PAST OR SURFACE FOUND AFTER GO/. ENTERING RESTART 2006 ILLEGAL PERMANENT IDENTIFIER FOLLOWS GO/. ENTERING RESTART 2007 W A LOGICALLY COMPLETE GO/ COMMAND WAS FOLLOWED BY OTHER DATA. SURPLUS CHECK SURFACES IGNORED 2008 W MORE THAN ONE CHECK SURFACE FOUND AFTER A GO COMMAND. SURPLUS CHECK SURFACES IGNORED 2009 ILLEGAL LANGUAGE USAGE ENCOUNTERED BEFORE DRIVE SURFACE. ENTERING RESTART 2010 W DRIVE SURFACE IS SUPPOSED 2011 ILLEGAL GOTO, FROM, INDIRV, INDIRP OR SRFVCT STATEMENT 2012 PARAMETER LIST TOO LONG 2013 ILLEGAL ARGUMENT 2014 W ONLY FIRST WORD AFTER SLASH IS EXAMINED. REMAINING WORDS IGNORED 2015 APPROPRIATE SURFACE IS NOT NAMED AFTER PSIS.COMMAND IGNORED.CONTINUING 2017 INPROPER FORMAT FOR JUMPTO. STATEMENT IGNORED 2018 SYN STATEMENT HAS NO ARGUMENTS OR AN ODD NUMBER OF ARGUMENTS 2019 SYN STATEMENT HAS A MAIN WORD NOT ADMISSABLE OR VALUE 2020 NO DRIVE SURFACE FOUND PRECEDING OTHERWISE ACCEPTABLE FORMATS 2022 AN ACCEPTABLE CHECK SURFACE IS NOT NAMED 2023 IDENTIFIER NOT PRECEDED BY ACCEPTABLE SURFACE. ENTERING RESTART 2024 W THE WORD INTOF WAS NOT PRECEDED BY A NUMBER.FIRST INTERSECTION ASSUMED 2025 MACRO VARIABLE NOT FUNCTION 2026 TOO MANY DIMENSIONED VARIABLES IN PART PROGRAM. RANGE TABLE FILLED 2027 INCORRECT FORMAT FOR RESERV STATEMENT. MUST BE SYMBOL,NUMBER 2028 W NO ARGUMENTS DESIRED. ARGUMENTS IGNORED 2029 ARGUMENT FOLLOWING ZSURF/ IS NOT A PLANE 2030 W NO ARGUMENTS FOLLOW PRINT/,PUNCH/,CFSAVE/,CONTRL/ OR PPOPTN/ . STATEMENT IGNORED 2031 W INVALID ARGUMENT FOLLOWS PRINT/, PUNCH/ OR CFSAVE/ . ARGUMENT IGNORED 2032 INVALID NUMBER OF ARGUMENTS IN CANON DEFINITION 2033 INVALID ARGUMENT IN CANON DEFINITION 2034 INVALID POCKET FORMAT 2035 W ONE TERM OF SYNONYM ARGUMENT PAIR IS NOT A VARIABLE 2036 IMPROPER ARGUMENT IN GOTO/PATERN STATEMENT 2037 BOTH OMIT AND RETAIN SPECIFIED IN GOTO/PATERN STATEMENT 2038 TOO MANY ARGUMENTS SPECIFIED IN GOTO/PATERN STATEMENT. ARGSTK TABLE OVERFLOW 2039 ILLEGAL ARGUMENT OR UNEVEN NUMBER OF ARGUMENTS IN PPOPTN STATEMENT 2040 ILLEGAL PATERN DEFINITION FORMAT 2041 TOO MANY ARGUMENTS IN INCR LIST 2042 W INVALID CONTROL STATEMENT. ARGUMENT IGNORED 2043 TOO MANY MACRO VARIABLES 2044 DUPLICATE NAME OF DIMENSIONED VARIABLES 2045 RESERV INVALID IN MACRO PROGRAM 2051 INVALID ARGUMENT IN OBTAIN STATEMENT 2052 INCORRECT NUMBER OF ARGUMENTS OR INVALID ARGUMENT 2053 INVALID INCLUSIV SUBSCRIPT FORMAT 2054 A,B AND C IN INCLUSIVE SUBSCRIPT FORMAT MUST BE EXPLICIT INTEGER 3001 NAME TABLE OVERFLOW

B.2 EXECUTION Errors

1 CANONICAL FORM NOT PREVIOUSLY CORRECTLY DEFINED IS BEING REFERENCED. 2 W THE FIRST LINE GIVEN FOR THE DEFINITION OF THE POINT IS NOT A VERTICAL PLANE. 3 W THE SECOND LINE GIVEN FOR THE DEFINITION OF THE POINT IS NOT A VERTICAL PLANE. 4 POINT UNDEFINED. INTERSECTION OF TWO LINES WHICH ARE TOO CLOSE TO PARALLEL. 5 LINE INVOLVED IS NOT VERTICAL PLANE. POINT IS UNDEFINED. 6 LINE AND CIRCLE DO NOT INTERSECT. POINT IS UNDEFINED. 7 CIRCLE IS NOT A VERTICAL CYLINDER. POINT IS UNDEFINED. 8 W THE GIVEN LINE IS VERTICAL. SUBSTITUTE Y FOR X IN 'XLARGE' OR 'XSMALL'. 9 W THE GIVEN LINE IS HORIZONTAL. SUBSTITUTE X FOR Y IN 'YLARGE' OR 'YSMALL'. 10 A VECTOR OPERAND IN A DOT PRODUCT COMPUTATION IS UNDEFINED. THE RESULT IS ZERO. 11 INPUT POINT IS NOT ON TABCYL, NER INTERSECTION POINT. 12 THE FIRST CIRCLE GIVEN FOR THE DEFINITION OF THE POINT IS NOT A VERTICAL CYLINDER. 13 THE SECOND CIRCLE GIVEN FOR THE DEFINITION OF THE POINT IS NOT A VERTICAL CYLINDER. 14 TRANSFORMATION MATRIX UNDEFINED. 15 THE LINE AND CONIC DO NOT INTERSECT. POINT IS UNDEFINED. 16 THE GENERAL CONIC EQUATION SHOULD NOT CONTAIN THE Z COORDINATE. POINT IS UNDEFINED. 17 TOO MANY TABCYLS INVOLVED IN THIS MOTION STATEMENT. 19 THE TWO GIVEN POINTS ARE TOO CLOSE TOGETHER. THE LINE CANNOT BE DEFINED. 20 THE ARGUMENT OF THE FUNCTION IS NEGATIVE; GOING ON WITH THE POSITIVE ARGUMENT. 21 THE FIRST CIRCLE GIVEN IN THE DEFINITION OF THE LINE IS NOT A VERTICAL CYLINDER. 22 THE SECOND CIRCLE GIVEN IN THE DEFINITION OF THE LINE IS NOT A VERTICAL CYLINDER. 23 THE CIRCLES USED IN THE DEFINITION OF THE LINE ARE CONCENTRIC. THE LINE IS UNDEFINED. 24 ONE OF THE CIRCLES USED IN THE DEFINITION OF THE LINE IS WHOLLY INSIDE OF THE OTHER. LINE IS UNDEFINED. 25 THE CIRCLES USED IN THE LINE DEFINITION INTERSECT, AND, THE MODIFIERS ARE NOT 'LEFT', 'LEFT' OR 'RIGHT', 'RIGHT'. 26 THE LINE GIVEN IN THE DEFINITION IS NOT A VERTICAL PLANE . LINE IS UNDEFINED. 27 THE DESIRED LINE IS UNDEFINED. THE GIVEN PLANES ARE EITHER PARALLEL, COINCIDENT OR BOTH VERTICAL. 28 THE INPUT LINE IS NOT A VERTICAL PLANE. CIRCLE IS UNDEFINED. 29 CIRCLE UNDEFINED. THE THREE GIVEN POINTS ARE COLLINEAR. 30 W THE THREE GIVEN POINTS ARE NOT IN THE SAME HORIZONTAL PLANE. 31 CIRCLE UNDEFINED. THE CIRCLE GIVEN IN THE DEFINITION IS NOT A VERTICAL CYLINDER. 32 VECTOR FOR CANTED TABCYL UNDEFINED. 33 TABCYL INPUT POINT UNDEFINED. 34 CONSECUTIVE INPUT POINTS ARE IDENTICAL. TABCYL UNDEFINED. 35 FOR XYZ-CASE, INCORRECT PARAMETERS SPECIFIED. TABCYL UNDEFINED. 36 THE INPUT-GEOMETRY OF THE NUMBER-FUNCTION IS UNDEFINED OR OF A WRONG KIND; THE RESULT IS 0. 37 THE LOG ARGUMENT IS ZERO; THE RESULT IS A NEGATIVE NUMBER. 38 THE ARSIN-ARCOS ARGUMENT IS ABSOLUT GREATER THAN 1; THE RESULT IS ZERO. 39 THE INPUT-GEOMETRIE AT THE VALUE-FETCHING IS UNDEFINED OR OF A WRONG KIND; THE RESULT IS 0. 40 W THE FETCH-INDEX AT THE VALUE-FETCHING IS UNDEFINED OR THE CANONICAL FORM IS TOO SHORT; THE RESULT IS 0. 41 THE FETCH-INDEX AT THE VALUE-FETCHING IS LESS OR EQUAL ZERO; THE RESULT IS 0. 42 THE PARAMETER-DELIVERY PRECEEDES NO EQUIVALENT INTERSECTION-STMT; THE RESULT IS 0. 43 THE PARAMETRIC-DELIVERY-FUNCTION IS NOT CORRECTLY SUPPLIED; THE RESULT IS 0. 44 THE SUM OF THE SQUARES OF THE COEFFICIENTS OF X, Y AND Z IS ZERO. PLANE NOT DEFINED. 45 W 'ZIGZAG' IS IGNORED SINCE PATERN IS NOT GRID. 46 'OMIT' HAS BEEN APPLIED (OR 'RETAIN' HAS NOT BEEN APPLIED) TO THE FIRST OR LAST POINT IN AN AVOID STRING. 47 CONE UNDEFINED. THE AXIS VECTOR GIVEN IN THE DEFINITION HAS ZERO VALUE. 48 CONE UNDEFINED. THE GIVEN ANGLE IS GREATER THAN 90 DEGREES. 49 W PLANE USED IN 'ZSURF' STATEMENT IS UNDEFINED. 'ZSURF' STATEMENT IS IGNORED 50 W PLANE USED IN 'ZSURF' STATEMENT IS PARALLEL TO Z AXIS. 'ZSURF' STATEMENT IS IGNORED. 51 INPUT VECTORS ARE PARALLEL. PLANE UNDEFINED. 52 THE THREE SIMULTANEOUS EQUATIONS DO NOT HAVE A UNIQUE SOLUTION. 53 'REFSYS' GIVEN WITH UNDEFINED MATRIX. TRANSFORMS WILL BE UNDEFINED. 54 AT LEAST ONE INPUT-ELEMENT OF THE SPAT-FUNCTION IS WRONG OR UNDEFINED; THE RESULT IS 0. 55 AT LEAST ONE INPUT-ELEMENT OF THE DIST-FUNCTION IS UNDEFINED; THE RESULT IS 0. 56 THE VECTOR WHOSE LENGTH IS TO BE COMPUTED IS UNDEFINED. A LENGTH OF ZERO IS USED. 57 SPHERE UNDEFINED. THE FOUR GIVEN POINTS ARE COMPLANAR. 58 CYLINDER UNDEFINED. THE AXIS VECTOR GIVEN IN THE DEFINITION HAS ZERO VALUE. 59 GIVEN PLANE IS PERPENDICULAR TO AN AXIS. MODIFIER MUST CONTAIN THIS AXIS. 61 THE INPUT-ELEMENT OF THE DIST-FUNCTION IS OF A WRONG KIND; THE RESULT IS 0. 62 THE TWO PLANES OR LINES OF THE DIST-FUNCTION ARE NOT PARALLEL; THE RESULT IS 0. 63 THE REQUESTED NUMBER OF ROWS OR COLUMNS IN A GRID OR PERIPHERAL PATERN IS ZERO OR A NEGATIVE NUMBER. 64 INCREMENT OR NUMBER OF INCREMENTS IN A PATERN DEFINITION INCREMENT LIST IS NEGATIVE OR ZERO. 65 VECTOR SUPPLIED IN A PATERN DEFINITION HAS LENGTH ZERO. 66 THE REQUESTED NUMBER OF POINTS IN A PATERN IS ZERO OR A NEGATIVE NUMBER. 67 THE PATERN USED IN A GRID OR PERIPHERAL PATERN DEFINITION MUST BE LINEAR. 68 A RANDOM PATERN MAY NOT BE USED IN THE DEFINITION OF A RANDOM PATERN. 69 INPUT POINT FOR LCONIC IS UNDEFINED. 70 TWO INPUT POINTS COINCIDE. THE CONIC CANNOT BE DEFINED. 71 W THIS IS A DEGENERATIC CONIC. 72 TABCYL INTERSECTION POINT IS NOT FOUND. 73 MORE THAN 1 POINT IN TANGENCY ON TABCYL. 74 TABCYL TANGENT LINE IS NOT FOUND. 75 TABCYL TANGENT LINE FAILED. 76 ARGUMENT FOR TABCYL TANGENT LINE IS UNDEFINED. 77 TABCYL MODIFIER INDETERMINATE. 78 TABCYL TANGENT CIRCLE IS NOT FOUND. 79 ARGUMENT FOR TABCYL TANGENT CIRCLE IS UNDEFINED. 80 AT LEAST ONE INPUT OF THE ANGL-FUNCTION IS UNDEFINED OR OF A WRONG KIND; THE RESULT IS ZERO. 82 A RANDOM PATERN OCCURS AS A SUB ELEMENT OF A RANDOM PATERN. 83 RESTART DUE TO DEFINITION OR SYNTAX ERROR. 84 W HALF SPACE MODIFIER NOT PROPERLY SPECIFIED. 85 REFERENCED ELEMENT NOT PROPERLY DEFINED. 86 BOUNDED GEOMETRY ELEMENT HAS BEEN REDEFINED WITH A DIFFERENT NUMBER OF ELEMENTS. 87 THE DIFFERENCE BETWEEN >P1< AND >P2< IS LESS THAN .01 88 >V1< IS PARALLEL TO THE CHORD. 89 INVALID OR ERRONEOUS CANONICAL FORM ENCOUNTERED. BOUNDED GEOMETRY PROCESSING TERMINATED. 90 TOO MUCH EMBEDDEDNESS IN BOUNDS AND OBJECT STATEMENTS. BOUNDED GEOMETRY PROCESSING TERMINATED. 91 INCORRECT ARGUMENT IN 'UNITS' STATEMENT. 92 W PLANE IS NOT VERTICAL. 93 SPECIFIED CL POINT DOES NOT EXIST. 200 WRONG ARGUMENT IN PARTPROGRAM CALLING FUNCTION. 3501 POCKET INPUT CONTAINS DUPLICATE POINTS. 3502 POCKET INPUT CONTAINS THREE COLLINEAR POINTS. 3503 POCKET INPUT POINTS ARE NOT COMPLANAR. 3504 POCKET INPUT POINTS DESCRIBE CONCAVE FIGURE. 3506 AN INPUT POINT IS UNDEFINED. 3507 THE ANGLE BETWEEN THE TOOL AXIS AND THE PLANE OF THE POCKET BOTTOM IS TOO SMALL (LESS THAN 12 DEGREES). 3510 LESS THAN 3 POINTS HAVE BEEN GENERATED. 3521 A MINOR WORD OR CANONICAL FORM IN THE INPUT STREAM IS IN THE WRONG POSITION OR INVALID. 3522 AN INPUT CANONICAL FORM HAS NOT BEEN DEFINED PROPERLY. 3523 AN INPUT CANONICAL FORM IS NOT SUITABLE FOR THIS APPLICATION. 3524 TOO MANY OR FEW PARAMETERS HAVE BEEN INPUT. 3551 THE CUTTER COULD NOT CONTACT THE PART SURFACE FROM THE PRESENT POSITION. 3552 AT THE LAST POINT DURING PATH GENERATION, THE SYSTEM COULD NOT MAKE A CUTTER STEPOUT THAT SATISFIED ALL CURVATURE AND TOLERANCE CONDITIONS. 3553 MORE CL POINTS WERE GENERATED IN A SINGLE PATH THAN PERMITTED BY 'NUMPTS' SETTING. 3554 THE TOTAL LENGTH OF THE CURRENT CUTTER PATH EXCEEDED THE 'MAXDP' SETTING. 3555 W UNABLE TO AVOID INTERFERENCE WITH CURRENT PARAMETERS 3561 A MINOR WORD OR CANONICAL FORM IN THE INPUT STREAM IS IN THE WRONG POSITION OR INVALID. 3562 AN INPUT CANONICAL FORM HAS NOT BEEN DEFINED PROPERLY. 3563 AN INPUT CANONICAL FORM IS NOT SUITABLE FOR THIS APPLICATION. 3564 TOO MANY OR FEW PARAMETERS HAVE BEEN INPUT. 3565 AN 'SCON' DATA AREA (DS,PS,FEED,ETC.) HAS NOT BEEN DEFINED OR HAS BEEN INCORRECTLY DEFINED. 3566 GENERAL APT ARELEM CONDITIONS FOR REGIONAL MILLING ARE INVALID (PROBABLY UNACCEPTABLE CUTTER TYPE). 3567 PART OR DRIVE GEOMETRY COULD NOT BE FETCHED BECAUSE OF DEFINITION ERROR OR SPACE LIMITATION. 5000 LARGE DATA COULD NOT BE STORED INTERNALY. 5001 WRONG SECOND PARAMETER IN SMESH DEFINITION. 5002 THE REQUESTED SYNTHETIC CURVE WAS NOT AVAILABLE. 5003 THE WORD 'AXIS' WAS NOT IN PROPER POSITION IN THE INPUT STREAM. 5004 A VALID AXIS WAS NOT DEFINED. 5005 THE WORDS 'CCLW' OR 'CLW' WERE NOT IN PROPER POSITION IN THE INPUT STREAM. 5006 TWO ANGLES ARE REQUIRED FOR SURFACE OF REVOLUTION. 5007 TWO POINTS OR ONE VECTOR ARE REQUIRED TO SPECIFY AN AXIS OF A CYLINDER. 5021 SEGMENT REFERENCED FOR DISSECTION ON FLOW CURVE IS OUT OF RANGE. 5022 THERE IS NOT ENOUGH ROOM IN BUFFER FOR DISSECTED SEGMENT. 5023 THERE IS NOT ENOUGH ROOM IN BUFFER TO DISSECT ONE ARC. 5024 AN ARC REFERENCED FOR DISSECTION IS OUT OF RANGE FOR THIS CURVE. 5025 THE WORD 'CROSS' WAS ENCOUNTERED TWICE IN A DEFINITION. 5026 LESS THAN TWO SPLINES WERE INPUT BEFORE 'CROSS'. 5027 AN INPUT CURVE WAS NOT PROPERLY DEFINED. 5028 THE FIRST INPUT CURVE COULD NOT BE FETCHED. 5029 THE FIRST INPUT CURVE WAS NOT A FLOW CURVE. 5030 TOO MANY CURVES HAVE BEEN INPUT FOR THE CURVE. DIRECTORY TABLE SIZE. 5031 THERE IS NOT ENOUGH BUFFER SPACE TO LOAD THIS CURVE. 5032 AN INPUT SPLINE CURVE COULD NOT BE FETCHED. 5033 THE NUMBER OF FLOW SEGMENTS DIFFERED BETWEEN TWO SPLINE CURVES. 5034 THERE IS NOT ENOUGH ROOM IN THE DIRECTORY TABLE FOR CROSS CURVES. 5035 THERE IS NOT ENOUGH BUFFER SPACE TO HOLD A CROSS CURVE. 5036 AN INPUT CROSS CURVE COULD NOT BE FETCHED. 5037 THE NUMBER OF FLOW SEGMENTS IN A CROSS CURVE DID NOT MATCH THE NUMBER OF SPLINES LESS ONE. 5038 THERE IS NO MATCH AT A SEGMENT JUNCTION POINT BETWEEN A SPLINE AND CROSS SPLINE CURVE. 5039 TWO CROSS CURVES PASS THROUGH THE SAME SPLINE JUNCTION POINTS. 5040 THERE IS NOT ENOUGH BUFFER SPACE TO FIT A CROSS CURVE THROUGH SPLINE JUNCTION POINTS. 5041 AN ERROR WAS ENCOUNTERED IN TRYING TO CROSS FIT A CROSS CURVE. 5043 THERE IS NOT ENOUGH BUFFER SPACE FOR A FLOW STRUCTURE ON A CROSS CURVE. 5044 THERE IS NOT ENOUGH BUFFER SPACE TO DETERMINE CROSS VECTORS BY SPLINING. 5045 CROSS FITTING FAILED AT A SEGMENT INTERIOR POINT. 5060 ERROR DURING READ OF A LARGE DATA ARRAY >LDA< FROM FILE 9. 5061 NOT ENOUGH ROOM IN >LDA<. 5062 NOT ENOUGH ROOM ON FILE 9. (EXTERNAL >LDA<). 5121 THE FIRST WORD IN THE SCURV DEFINITION DID NOT CORRESPOND TO ONE OF THESE PROGRAMMED. 5122 AN ARGUMENT IN A PRIMARY CURVE DEFINITION WAS NOT A RECOGNIZED ONE. 5123 THE MAXIMUM NUMBER OF POINTS IN A PRIMARY CURVE DEFINITION HAS BEEN EXCEEDED. 5124 A VECTOR CONSTRAINT HAS BEEN INPUT PRIOR TO THE FIRST POINT. 5125 A VECTOR ARGUMENT DID NOT FOLLOW A MINOR WORD WHICH REQUIRED A VECTOR CONSTRAINT. 5126 A 'REAL' ARGUMENT DID NOT FOLLOW A 'WEIGHT' SPECIFICATION. 5127 A 'REAL' ARGUMENT DID NOT FOLLOW A 'LIMIT' SPECIFICATION OR AN INPUT CURVE TO THE 'COMBIN' STATEMENT HAS NOT BEEN SUCCESSFULLY DEFINED. 5128 THE JUNCTION POINTS OF TWO CONSECUTIVE CURVES IN 'COMBIN' DEFINITION DID NOT MATCH. 5129 W THE TANGENT VECTORS AT THE JUNCTION OF CONSECUTIVE CURVES IN A 'COMBIN' DEFINITION HAD DIFFERENT DIRECTIONS. 5130 CURVES WITH FLOW STRUCTURE CANNOT BE COMBINED YET. ERRORS IMPOSING FLOW RATES ACROSS SYNTHETIC CURVES. 5152 SEGMENT NUMBER OF THE 'SCURV' IS NOT CORRECT. 5153 PATCH NUMBER OF THE 'SSURF' IS NOT CORRECT. 5154 PARAMETER SPECIFICATION IS NOT CORRECT. 5155 THE LENGHT OF A VECTOR IS TOO SMALL TO NORMALIZE. 5156 THE INTERSECTION POINT CANNOT BE DEFINED. 5157 INPUT CANON FORM NOT PREVIOUSLY DEFINED. 5158 DEFINITION ERROR. 5159 SPECIFIED VECTOR OR POINT DOSE NOT EXIST. 5160 SURFACE NORMAL NOT PROPERLY DEFINED 5210 MAXIMUM BUFFER SPACE FOR A 'MESH' DEFINITION EXCEEDED. 5211 TOO MANY POINTS IN ONE SPLINE OR CROSS SPLINE FOR CURRENT CURVE FITTING ALGORITHM. 5212 A POINT WAS MISSING. 5213 TOO MANY POINTS FOR SPACE AVAILABLE IN SSPAD. 5214 THE NEXT ENTRY SHOULD BE 'NORMAL' , BUT IT WAS NOT RECOGNIZABLE. 5215 THE NEXT ENTRY SHOULD BE A VECTOR. 5216 THE NEXT ENTRY SHOULD BE 'TANSPL', BUT IT WAS NOT RECOGNIZABLE. 5217 THE NEXT ENTRY SHOULD BE 'CRSSPL', BUT IT WAS NOT RECOGNIZABLE. 5218 THE NEXT ENTRY SHOULD BE 'WEIGHT', BUT IT WAS NOT RECOGNIZABLE. 5219 THE NEXT ENTRY SHOULD BE A SCALAR. 5220 THE NEXT ENTRY SHOULD BE 'LIMIT', BUT IT WAS NOT RECOGNIZABLE. 5222 UNRECOGNIZED DATA WAS ENCOUNTERED IN THE MESH INPUT STREAM OR ELSE THE NUMBER OF INPUT POINTS WAS INCORRECT. 5300 SMESH INPUT POINTS ARE NOT LINEAR. 5331 TYPE DEFINITION IS MISSING IN 'MESH' INPUT. 5352 NUMBER OF SPLINES MUST BE AT LEAST TWO. 5353 THE SURFACE SIZE EXCEEDED A PROGRAMMED MAXIMUM IN 'REVOLV' 5354 THE AXIS VECTOR OF THE CYLINDER WAS NOT SPECIFIED CORRECTLY. 5355 ALL POINTS OF THE CURVE LIE ON THE AXIS OF REVOLUTION. 5356 CROSS SECTION CURVE DEFINITION FAILS. 5371 NOT ENOUGH SPACE TO FETCH CURVE. 5373 CURVE COULD NOT BE FETCHED. 5374 NOT ENOUGH SPACE TO FETCH CROSS CURVE. 5375 CURVE NOT DEFINED. 5376 CROSS CURVE COULD NOT BE FETCHED. 5377 CHECK FOR ENOUGH ROOM FOR SURFACE IN 'SURF'. 5378 SYSTEM ERROR. ARRAY >IB< DIMENSION MUST BE INCREASED. 5379 INVALID INDEX, SYSTEM ERROR. 5391 SPLINE CURVE COULD NOT BE GENERATED. 5392 CROSS SPLINE CURVE COULD NOT BE GENERATED. 5393 PROBLEMS WITH INNER POINTS. 5396 TWIST VECTORS CANNOT BE COMPUTED. 5402 COULD NOT FIND THE MINIMUM DISTANCE BETWEEN CUTTER AND A SCULPTURED SURFACE. 5403 SS ROUTINE CALLED EXCESSIVE NUMBER OF TIMES WITHOUT A SUCCESSFUL TOOL POSITION BEING FOUND. 5502 LENGTH OF NORMAL VECTOR WHICH CONTROLS DIRECTION OF CHORDAL PROJECTION IS TOO SMALL. VECTOR IS ZERO. 5503 ANGLE BETWEEN CHORD AND THE DIRECTION OF CHORDAL PROJECTION IS TOO CLOSE TO ZERO. CHORDAL DIRECTION >D< AND VECTOR >V< ARE PERPENDICULAR. 5504 ANGLE BETWEEN SOME TANGENT VECTORS ON THE CURVE AND THE PROJECTION CHORD IS TOO CLOSE TO 90 DEGREES. A PARTICULAR TANGENT VECTOR ON THE CURVE AND VECTOR >V< ARE PERPENDICULAR. 5505 AT SOME POINT THE CURVE HAS REVERSED ITS DIRECTION ON THE CHORD OF PROJECTION. A PARTICULAR TANGENT VECTOR ON THE CURVE AND VECTOR >V< ARE MOVING IN OPPOSITE DIRECTIONS. 5506 COULD NOT FIT PROJECTION FLOW ON THE CHORD USING AVAILABLE SPACE. CHECK CHORD TO CURVE RELATIONSHIP OR ELSE INCREASE BUFFER SPACE. THE AVAILABLE SPACE FOR FLOW SPLINE >FL< HAS BEEN FILLED. 5507 THE CHORDAL PROJECTION FLOW RATE COULD NOT BE FIT AT SOME POINT OF THE CURVE. CHECK CURVE TO CHORD RELATIONSHIP. NOTE: CURVE SHOULD NEVER BE PERPENDICULAR TO CHORD. AN ARC HAS BEEN SUBDIVIDED 10 TIMES AT THE CURRENT POSITION WITHOUT BEING ABLE TO SUCCESSFULLY FIT THE FLOW OF 'COONS' PARAMETER IN THE CHORDAL PARAMETER. 5508 COULD NOT FIT ANGULAR FLOW WITHIN AVAILABLE SPACE. CHECK CURVE TO FOCAL POINT RELATIONSHIP OR INCREASE BUFFER SPACE. THE AVAILABLE SPACE IN >FL< USED UP. 5513 THE LAST JUNCTION POINT REFERENCED ON A PREVIOUS 'FLOW' DETAIL COMMAND DID NOT EQUAL THE FIRST JUNCTION POINT IN THE DETAIL COMMAND. 5514 AN ARC JUNCTION POINT REFERENCED IN A 'FLOW' DETAIL COMMAND WAS NOT WITHIN RANGE FOR THE CURVE. 5515 THE FINAL JUNCTION POINT REFERENCED IN THE FINAL FLOW DETAIL COMMAND WAS NOT THE LAST POINT OF THE CURVE. 5516 THE LAST JUNCTION POINT REFERENCED IN A PREVIOUS 'SEGMENT' DETAIL COMMAND DID NOT EQUAL THE FIRST JUNCTION POINT IN THE PRESENT DETAIL COMMAND. 5517 AN ARC JUNCTION POINT REFERENCED IN A 'SEGMENT' DETAIL COMMAND COMMAND WAS NOT WITHIN RANGE FOR THE CURVE. 5518 THE FINAL JUNCTION POINT REFERENCED IN THE FINAL 'SEGMENT' DETAIL COMMAND WAS NOT THE LAST POINT OF THE CURVE. 5520 A 'FLOW' DETAIL COMMAND WORD IS INVALID. 5521 THE TWO POINTS AVAILABLE FOR DEFINING A PROJECTION CHORD ARE TOO CLOSE TO DETERMINE A CHORD. 5522 THERE WAS NOT ENOUGH BUFFER SPACE FOR A 'FLOW' DETAIL PARAMETERIZATION COMMAND. 5751 IN A 'CURSEG' DEFINITION ALL OF THE POINTS DO NOT LIE IN A PLANE. 5752 IN A 'CURSEG' DEFINITION ALL OF THE TANGENT CONSTRAINTS DO NOT LIE IN A PLANE. 5753 MORE THAN 5 CONDITIONS IN A 'CURSEG' DEFINITION. 5760 IN A 'CURSEG' DEFINITION END SLOPES ARE PARALLEL (THAT IS, THEY DO NOT INTERSECT). 5770 IN A 'CURSEG' DEFINITION, THE POINTS INDICATE AN IMPOSSIBLE INFLECTION. 5772 NO SUITABLE CONIC CURVE FITS THE SPECIFIED CONDITIONS. 5901 THERE ARE FEWER THAN TWO POINTS IN THE SPLINE. 5902 TWO CONSECUTIVE POINTS ARE IDENTICAL ('SPLINE' CASE). 5903 TWO OF THE INPUT POINTS ARE IDENTICAL ('CURSEG' CASE). 5904 SMOOTHING ALGORITHM FAILED. 5905 A VECTOR CONSTRAINT WAS ZERO. 5906 PROJECTION OF >TANSPL< ON THE PLANE PERPTO NORMAL IS TOO SMALL. 5907 PROJECTION OF >CRSSPL< ON THE PLANE PERPTO NORMAL IS TOO SMALL. 5908 TWO OR MORE CONSTRAINT VECTORS AT ONE POINT LIE IN THE SAME DIRECTION. 5909 PARABOLIC INTERPOLATION FAILED AT ONE END OF A 'SPLINE'. 5910 THE MID POINT OF THREE CONSECUTIVE POINTS PROJECTED OUTSIDE THE RANGE OF THE SURROUNDING TWO. 5921 A DISTANCE BETWEEN TWO CONSECUTIVE INPUT POINTS IS TOO SMALL. 5922 INPUT >IDC< IS NOT SIGNIFICANT. 5923 ERROR IN SOLVING SIMULTANEOUS LINEAR EQUATIONS. 5924 NUMBER OF INPUT POINTS IS LESS THAN 3. 5925 A DISTANCE BETWEEN TWO CONSECUTIVE OUTPUT POINTS IS TOO SMALL. 5926 AN OUTPUT FIRST ORDER DERIVATIVE HAS A MAGNITUDE WHICH IS TOO SMALL. 20001 MORE THAN 2 CHECK SURFACES FOR THIS CUT SEQUENCE. 20101 PART SURFACE IS A POINT. 20102 CUTTER WAS NOT WITHIN TOLERANCE OF DS AT START OF CUT. 20103 CUTTER WAS NOT WITHIN TOLERANCE OF PS AT START OF CUT. 20104 UNABLE TO DETERMINE GENERAL DIRECTION OF FIRST CUT VECTOR. 20105 FWD DIRECTION COULD NOT BE DETERMINED. 20106 INITIAL MOTION DIRECTION VECTOR OR ITS ORIENTATION COULD NOT BE DETERMINED. 20107 CUTTER NOT DEFINED PRIOR TO CUT SEQUENCE CALCULATION. 20108 'FROM' POINT NOT SPECIFIED. 20109 'MOTION' MODIFIER ('ON','TO','PAST','TANTO','PSTAN') NOT SPECIFIED. 20110 CHECK SURFACE MISSING FOR THIS 'MOTION' STATEMENT. 20201 CUTTER NOT DEFINED PRIOR TO CUT SEQUENCE CALCULATION. 20202 FROM POINT NOT SPECIFIED. 20203 MORE THAN ONE CHECK SURFACE SPECIFIED IN A STARTUP. 20204 'NOPS' IN EFFECT, BUT PS SPECIFIED IN STARTUP. 20205 STARTUP ITERATION FAILED TO CONVERGE. 20206 INVALID DATA FOR STARTUP. (SEE COMPUTER PROGRAMMER). 20901 INDIRP VECTOR HAS NO LENGTH. 20902 DIRECTION OF MOTION GIVEN WITHOUT A STARTING POINT BEING GIVEN. 20903 W CANNOT DETERMINE SURFACE TYPE. DS ASSUMED. 21001 INDIRV VECTOR HAS NO LENGTH. 21002 DIRECTION OF MOTION GIVEN WITHOUT A STARTING POINT BEING GIVEN. 21003 W CANNOT DETERMINE SURFACE TYPE. DS ASSUMED. 21101 SRFVCT VECTOR HAS NO LENGTH. 21102 W CANNOT DETERMINE SURFACE TYPE. DS ASSUMED. 21301 DIRECTION OF MOTION GIVEN WITHOUT A STARTING POINT BEING GIVEN. 22001 NO DRIVE SURFACE NAMED AFTER GO/. ENTERING RESTART MODE. 22002 ITEM NOT 'FEDRAT','TO','ON','PAST' OR SURFACE FOUND AFTER G0/. ENTERING RESTART MODE. 22003 ILLEGAL PERMANENT IDENTIFIER FOLLOWS GO/. ENTERING RESTART MODE. 22004 ILLEGAL LANGUAGE USAGE ENCOUNTERED BEFORE DRIVE SURFACE. ENTERING RESTART MODE. 22201 INVALID CUTTER DEFINITION FORMAT. 22202 CUTTER DIAMETER IS NEGATIVE. 22203 CUTTER HEIGHT IS NEGATIVE. 22204 CUTTER ANGLES (ALPHA AND BETA) ARE TOO LARGE. 22205 CUTTER ANGLE ALPHA IS NEGATIVE. 22206 DIAMETER, ALPHA AND HEIGHT OF CUTTER ARE INCONSISTENT. 22207 W CUTTER ANGLE BETA IS NEGATIVE. 22208 CORNER RADIUS OF CUTTER IS NEGATIVE. 22209 CORNER CIRCLE CENTER IS INCONSISTENT WITH UPPER LINE SEGMENT OF CUTTER. 22210 CORNER CIRCLE OF CUTTER INTERCEPTS LOWER LINE SEGMENT AT AN UNACCEPTABLE ANGLE. 22211 W INCONSISTENT CUTTER DEFINITION. LOWER LINE SEGMENT IGNORED. 22212 NO UPPER LINE SEGMENT ON CUTTER, OR CORNER CIRCLE MEETS LOWER LINE SEGMENT INCORRECTLY. 22213 CORNER CIRCLE OF CUTTER DOES NOT INTERSECT LOWER LINE SEGMENT. 22214 CORNER CIRCLE OF CUTTER DOES NOT INTERSECT UPPER LINE SEGMENT. 22215 CORNER CIRCLE OF CUTTER INTERSECTS UPPER LINE SEGMENT AT UNACCEPTABLE ANGLE. 22216 W INCONSISTENT CUTTER DEFINITION. UPPER LINE SEGMENT IGNORED. 22217 CUTTER DEFINITION NOT VALID. 22218 WRONG DATA IN TLINC, NO ARC OR NO LINE 22219 NO CUTTER DEFINED TO COMPUTE DISC RADIUS RA OR DISC HEIGHT HI. 22220 POINT IS OUTSIDE OF THE U/V PARAMETERS OF A PATCH. 22221 R1 IS LESS THAN THE TOLERANCE. 22222 THE TOOL AXIS CANNOT BE COMPUTED. 22223 WRONG TOOL AXIS INFORMATION. 22300 W A 'TLAXIS' COMMAND HAS BEEN USED WITHOUT A PREVIOUS 'MULTAX' COMMAND. NO TOOL AXIS VALUES OUTPUTTED. 22301 TOO MANY PARAMETERS IN A 'TLAXIS' STATEMENT. EXCESS VALUES IGNORED. 22401 W A 'MULTAX' COMMAND HAS BEEN USED FOLLOWING PREVIOUS MOTION OUTPUT WITHOUT TOOL AXIS VALUES. 22701 W 'THICK' GIVEN FOR MORE THAN THE ALLOWED NUMBER OF SURFACES. EXTRA VALUES IGNORED. 22801 REGION DATA BELONGS TO MORE THAN ONE SURFACE. 22802 LESS THAN 3 POINTS AS REGION BOUNDARY. 22803 REGION BOUNDARY IS INCORRECT. 22804 REGION BOUNDARY CONTAINS INTERSECTIONS. 22805 TOO MANY REGION POINTS TO PROCESS. 22806 REGION DATA CANNOT BE FETCHED. 22830 GEOMETRY ELEMENT IS NOT DEFINED - RETURN WITHOUT RESULT. 22831 NO INTERSECTION POSSIBLE. 22832 SAME SSURF FOUND TWICE BEFORE >WITH< ONLY FIRST FOUND SSURF IN FIRST PART OF THE STATEMENT WILL BE USED. 22833 SAME SSURF FOUND TWICE AFTER >WITH< ONLY FIRST FOUND SSURF IN SECOND PART OF THE STATEMENT WILL BE USED. 22834 SAME SSURF WILL BE INTERSECTED BY ITSELF THIS IS NOT POSSIBLE. 23401 SURFACE TYPE NOT IDENTIFIABLE. (SEE COMPUTER PROGRAMMER) . 23500 CANONICAL FORM OF SURFACE UNDEFINED. 23901 CUTTER NOT WITHIN TOLERANCE OF DS AT START OF CUT. 23902 DS AND CS CIRCLES HAVE SAME CENTER. 23903 DS AND CS NOT TANGENT AS STARTED. 23904 REQUESTED FINAL CUTTER POSITION NOT POSSIBLE. 23905 DS DOES NOT INTERSECT CS GOING IN SPECIFIED DIRECTION. 23908 CS AND DS DO NOT INTERSECT. 24001 CUT VECTOR ITERATION TO DS AND PS FAILED. 24002 CUT VECTOR ITERATION TO CS FAILED. 24003 'NUMPTS' COUNT EXHAUSTED. MISSED CS OR CUT SEQUENCE IS TOO LONG. 24004 COULD NOT DETERMINE TRIAL MOVE ALONG DS AND PS. CHECK CUTTER TO SURFACE CONFIGURATION. 24005 MAXIMUM CUT SEQUENCE LENGTH EXCEEDED. CS COULD NOT BE FOUND. 24006 MULTIPLE CS ERROR. (SEE COMPUTER PROGRAMMER). 24007 W NEGATIVE DISTANCE TO CS AT START OF CUT 24201 W CUTTER IS MOVING AWAY FROM CS. 24202 W DISTANCE TO TANGENT CS STOPPING POSITION CANNOT BE DETERMINED. 24401 W ITERATION TO PS, DS, CS GONE THRU RESTART ROUTE. 24402 CENTER CSNR EXIT TAKEN DURING PLANE ROUTINE ITERATION. (SEE COMPUTER PROGRAMMER) . 24403 CS NOT FOUND IN MOVE ALONG DS AND PS PLANES. 24404 MAXIMUM CUT SEQUENCE LENGTH EXCEEDED. CS COULD NOT BE FOUND. 25001 W DIFFICULTY ENCOUNTERED IN ITERATING CUTTER TO SURFACES. 25002 CANNOT ITERATE CUTTER INTO SPECIFIED SURFACES. 25003 COULD NOT DETERMINE NEW TOOL AXIS DURING 5 AXIS CALCULATION. (SEE COMPUTER PROGRAMMER). 25004 5 AXIS ITERATION DID NOT CONVERGE. 25005 TANGENT CS STOPPING POSITION COULD NOT BE DETERMINED. 25007 5 AXIS COUNT EXHAUSTED. 25008 TANGENT CS AND PS/DS-NORMALS NEARLY ORTHOGONAL. CHECK PART PROGRAM. 25009 TWO PLANES, NOT PERPENDICULAR TO THE XY PLANE, CANNOT BE USED AS DS AND CS FOR 'TANTO' CASE. 25402 COULD NOT FIND AN INTERSECTION BETWEEN TOOL RAY AND SURFACE. 25403 TOO MANY CALLS TO DDSSRF WITHOUT DETERMINING A NEW CUTTER POSITION. 26001 W MODIFIED FLIPCK TEST PASSED. 26002 COULD NOT DETERMINE NORMAL DISTANCE DIRECTION BETWEEN CUTTER AND SURFACE. 26201 W INITIAL PREFERRED DIRECTION DOES NOT INTERSECT SURFACE. 26202 COULD NOT CALCULATE SURFACE NORMAL AT SURFACE POINT (SEE COMPUTER PROGRAMMER). 26203 SYNTHETIC CURVE NOT NOW PROGRAMMED FOR ARELEM 26204 RADAR EXHAUSTED ALL TRIES 26401 COULD NOT CALCULATE UI VECTOR STARTING WITH TWO OR MORE DIRECTIONS. (SEE COMPUTER PROGRAMMER). 26601 CUTTER REFERENCE POINT AND SURFACE CENTER OF CURVATURE COINCIDE. 26602 UNABLE TO CALCULATE SATISFACTORY TOOL NORMAL. 26801 W DIFFICULTY IN LOCATING SURFACE. 26802 ZERO TOOL NORMAL. (SEE COMPUTER PROGRAMMER). 26803 COULD NOT FIND DIRECTION VECTOR THAT INTERSECTS THE SURFACE. 27001 W 'NODER' OR 'DERIV' NOT DEFINED. INCONSISTENT WITH PARAMETRIC SURFACE SOUBROUTINE. MODIFIER DISREGARDED. 27002 COULD NOT PERFORM ARELEM COMPUTATION DUE TO ZERO SURFACE NORMAL. CHECK DERIVATIVES IN PARAMETRIC SUBROUTINE. 27003 PARAMETRIC SURFACE FAMILY PARAMETER IS NOT DEFINED. 27004 PARAMETRIC SURFACE PARAMETER >U< IS NOT DEFINED. 27005 PARAMETRIC SURFACE PARAMETER >V< IS NOT DEFINED. 27206 THE PARAMETRIC SUBROUTINE (LOAD MODULE) DOES NOT EXIST IN JOB LIBRARY. 28801 W CANNOT ITERATE TO A ROOT OF THE CUBIC EQUATION IN THIS SEGMENT. 29001 A TOO MANY STATEMENTS IN THIS PART PROGRAM. 29002 A LARGEST CANONICAL FORM IS TOO LARGE. 29003 A INDEX OUT OF RANGE. 29004 A SYSTEM ERROR. ILLEGAL I.L. INSTRUCTION. 29006 A SYSTEM ERROR. ILLEGAL CALL I.L. INSTRUCTION. 29007 A UNDEFINED LABEL REFERENCED.

B.3 CLEDITOR Errors

30001 INVALID VTLAXS STATEMENT. 30002 A VTLAXS/OFF COMMAND WAS GIVEN WITHOUT A VTLAXS/ON COMMAND OR A PREVIOUS VTLAXS ERROR OCCURRED. 30003 TWO VTLAXS/ON COMMANDS WERE GIVEN WITHOUT A VTLAXS/OFF COMMAND BETWEEN THEM. 30004 A FROM COMMAND WAS GIVEN BETWEEN A VTLAXS/ON COMMAND AND ITS CORRESPONDING VTLAXS/OFF COMMAND. 30005 A VTLAXS COMMAND WAS GIVEN WITHOUT A PREVIOUS MOTION OR FROM COMMAND. 30006 A VTLAXS COMMAND WAS GIVEN WITHOUT A PREVIOUS MULTAX COMMAND. 30008 VTLAXS ERROR. CORNER RADIUS IS GREATER THAN THE CUTTER RADIUS. 30009 VTLAXS ERROR. CORNER RADIUS MUST BE ZERO WHEN USING ZSMALL. 30010 NO MOTION BETWEEN A VTLAXS/ON AND A VTLAXS/OFF. 30011 TRACUT WAS GIVEN BETWEEN A VTLAXS/ON AND ITS CORRESPONDING VTLAXS/OFF. 30012 COPY WAS GIVEN BETWEEN A VTLAXS/ON AND ITS CORRESPONDING VTLAXS/OFF. 30013 INCORRECT MODIFIER IN A COPY COMMAND. 30014 INDEX NUMBER NOT DEFINED. 30015 INCORRECT NUMBER OF PARAMETERS IN THE COPY COMMAND. 30016 THE PARAMETER 'N' IN THE COPY IS ZERO OR NEGATIVE. 30017 MIRROR, MIRROR ON THE WALL, YOU ARE NOT ALLOWED AT ALL. 30018 COPY LOGIC ERROR. CHECK PART PROGRAM FOR OVERLAPPING COPY AREAS OR AN ILLEGAL TRANSFER INTO COPY LOOP. 30019 COPY IS OVER 3 NEST LEVELS. 30020 INDEX NUMBER PREVIOUSLY USED. 30021 TOO MANY INDEX/N COMMANDS. 30024 SYSTEM FAILURE. POSITIONING ERROR IN COPY LOGIC. CHECK COMPUTER PROGRAMMER. 30025 BAD PARAMETER IN THIS CLDAT STATEMENT. 30026 THE FIRST RECORD NUMBER GIVEN IN THE CLDAT STATEMENT WAS NOT FOUND IN OLD CLFILE. 30027 EXFILE FORMAT ERROR. UNRECOGNIZABLE COMMAND. FRAME SIZE IS LESS THAN ZERO IN WIDTH OR LENGTH. 30030 UNIDENTIFIED POST PROCESSOR COMMAND. 30031 THE LAST RECORD NUMBER GIVEN IN THE CLDAT STATEMENT WAS NOT FOUND IN OLD CLFILE. 30032 INVALID CLFILE RECORD. RUN TERMINATED. 30034 NO COPY TRANSFORMATION HAS BEEN PERFORMED BECAUSE AN ERROR HAS OCCURRED INSIDE THE COPY LOOP. 30035 THE LIMIT ON THE NUMBER OF LENGTH OF POSTPROCESSOR TYPE COMMANDS AFTER A HOLDPP COMMAND HAS BEEN EXCEEDED. 30036 THE FOLLOWING VTLAXS SEQUENCE HAS NOT BEEN PROCESSED BECAUSE AN ARELEM ERROR HAS OCCURRED WITHIN IT. 30037 AN ARELEM RESTART ERROR HAS CAUSED CL PRINTOUT STARTING AT THE CL POINT PRECEDING THE ERROR INFORMATION. 30038 ERRONEOUS UNITS COMMAND.